Three years ago I started building models again, because it can be quite relaxing during a pandemic. Although I didn't have the opportunity to participate in tabletop rounds with friends, I could start building terrain or buildings and get more involved with my 3D printer. Since the overall interest in this topic has increased, I will also publish some articles here in the future. These will have different requirements. Some will be suitable for beginners, others more for professionals. To get you started, today we are building desert sand bases that can be easily replicated by beginners.--[ 1 - Build
I actually build everything myself out of Foam and other materials, but decided against it this time. Why not build some really generic sandbases that I printed out from my 3D printer beforehand. I had never done that before and really wanted to try it out. This also allowed me to test the quality of the prints at the same time, as I have many other ideas for projects that are in the tabletop realm. I have downloaded the small rock cluster from daandruff and will adapt this to my needs.
Even though I like these models, they are a little too small for me. To change that we use chipboard. Chipboard is stronger than cardboard and weaker than wood. I use the material every now and then to build natural round bases. So you can work chipboard with a modeling knife and small saws. We put the bases on the chipboard and draw around the platic models with a pencil. Try not to draw too neatly, because then the shapes will look more natural. We then saw out the shapes with a small hacksaw.
With a sharp modeling knife we can then smooth the edges so that it does not look so unnatural. Please make sure that you do not cut your hand, because this can easily happen. Unfortunately, there is no other (good) way to round off the edge of the base. After that we glue the stone plastic models with hot glue on the bases.
In the next step we will add some details to the bases to make them look more interesting. As we can imagine, there are not only stones in a desert, but also sand, pebbles, formations and remains of people or animals. The skull set from Citadel is quite good for sticking human or animal skulls on the bases. The set is expensive but will last a very long time. Sand is also a good way to customize the look of the base. To do this, we smear the bottom of the base with wood glue and pour sand and small stones over it. Again, you can use sand that you have ordered online or sandbox sand.This should then but then previously poured through a small sieve, so that really only sand is present and not any foreign material. I have also built small desert witches from old 3D printer material. These looked then later however rather like alien worm sausages. Nevertheless, you should try out a lot, because that's what makes building sand desert bases fun. We glue all components to the bases with super glue.
After we build our bases we let them dry. I let them dry for 24 hours because of the wood glue, so I can be sure that as few parts as possible fall off during the paint job.
Unfortunately, I noticed at this point that my black Chaos Black Primer is all and wanted to order new. Unfortunately there were some problems. If you want to have Chaos Black Primer delivered, you have to check your age. I don't want to know why and I don't want to give my age to buy a can of primer. Why do you have to be 18 years old to buy a can of primer? Ridiculous. At a German dealer the primers cost almost twice as much. So I decided to try another brand and tried the Montana Spray Primer in White. The result is really bad. Although the base was sealed, but not primed. Only the area with the super glue was primed and the rest was not. With this base, I applied two layers and also shook the can for a few minutes beforehand. The quality is really not what I expected from a quality brand like Montana. I had previously bought other primer from the same brand, which was really good but there was no longer in the store and to order something took me too long. So in the future I will have to look for a Chaos Black alternative whose brand does not come from a country that was so stupid to leave the EU.
So that my base has a good base color, I chose Army Painter Dirt Splatter. This I quickly applied and also not neatly worked, because that is not necessary. The other colors should only take over the base color of the base.
The first pass consists of the following layers. First, I primed everything with Wooden Deck Tan. This time I worked properly. Then I dry brushed everything with Averland Sunset to set accents. The last thing I did was to apply a strong tone wash for shades and higlights. All layers need enough time to dry.
Now I apply a strong drybrush with Lonbeard Grey. Almost all the colors underneath are painted over again. But only almost. This is a very interesting process, because a very small part of the colors will still be visible later and perceived by the viewer as a detail. Then I apply a finer drybrush with Praxeti White, but make sure not to use too much color. The skulls are also incorporated. Since I have no colors for bones and skeletons, I had to improvise a little at this point.
Now we just need to take care of the details. I drybrushed the skulls once again very carefully with Praxeti White. At this point you can bring out much more with some colors, but that was not possible at the moment. What also always looks good on a homemade base are the Battlefields Highland Tufs. However, you should not apply these on every base, but only in some special places. You don't need extra glue for the tufs, because they have little glue pads attached to the bottom. You just pull off a piece of tape and put them where you want them. After that our sand desert bases are ready and we can use them in our next adventure.